Single Skin Panels
The panels used in the construction of DASHPROJECTS Pre-Engineered Buildings are composed of the following:
Base metal of either Galvalume coated steel conforming to ASTM
Pre- Engineered Buildings
Basic Building Parameters
The basic parameters that define a pre-engineered building are: Building width, Building length, Building height, Roof slope, End bay length, Interior bay length and Design loads.
- Width: No matter what primary framing system is used, the building width is defined as the distance from outside of eave strut of one sidewall to outside of eave strut of the opposite sidewall. Building width does not include the width of Lean-To buildings or roof extensions.
- Length : The longitudinal length of the building measured from out to out of end wall steel lines.
- Height : Building height is the eave height which usually is the distance from the bottom of the main frame column base plate to the top outer point of the eave strut. When columns are recessed or elevated from finished floor, eave height is the distance from finished floor level to top of eave strut.
- Roof Slope ( x/10) : This is the angle of the roof with respect to the horizontal. The most common roof slopes are 0.5/10 and 1/10. Any practical roof slope is possible.
- End bay length : The distance from outside of the outer flange of endwall columns to center line of the first interior frame column.
- Interior bay length : The distance between the center lines of two adjacent interior main frame columns. The most common bay lengths are 6 m, 7.5 m and 9 m.
- Design Loads : Roof Live Load: 0.57 kN/m2
- Design Wind Speed: 110 km/h
Design for snow loads, earth quake loads, collateral loads, crane loads or any other loading condition, if required must be specified at the time of request for quotation.
Loads are applied in accordance with the latest American codes and standards applicable to pre-engineered buildings unless otherwise requested at the time of request for quotation.
Primary Framing
DASHPROJECTS pre-engineered buildings are custom-designed to meet your exact requirements. The most common Primary Framing systems are shown below. Practically any frame geometry is possible. Consult a DASHPROJECTS representative for your specific requirements.
Primary Build-Up Members: Minimum yield strength is 34.5 kN/ cm2
At DASHPROJECTS we can produce other non-standard main frames, of almost any configuration, if required.
High grade steel plate conforming to ASTM A 572M Grade 345. Factory painted with a minimum of 35 microns (DFT) of corrosion protection primer.
Frame Types:
Clear Span
Clear-Span (Arched)
Lean-To
Multi Gable
Multi-Span (Arched) AMS-1
Multi-Span 1
Multi-Span 2
Multi-Span 3
Roof System
Single Slope
Secondary Framing
Purlins, girts and eave struts are secondary structural members used to support the wall and roof panels. Purlins are used on the roof; girts are used on the walls and eave struts are used at the intersection of the sidewall and the roof.
Secondary members have two other functions:
- Act as struts that help in resisting part of the longitudinal loads that are
applied on the building such as wind and earthquake loads - Provide lateral bracing to the compression flanges of the main frame members
thereby increasing frame capacity.
Purlins, girts and eave struts are available in high grade steel conforming to ASTM A 607 Grade 50 or equivalent, available in 1.5 mm, 1.75 mm. 2.0 mm, 2.25 mm, 2.5 mm and 3.0 mm thickness. pre-They come with a pre-galvanized finish, or factory painted with a minimum of 35 microns (DFT) of corrosion protection primer.
Minimum yield strength is 34.5 kN/ cm2
Applications of PEB
Nearly 70% of all single storey non-residential construction now utilizes preengineered buildings. Applications range from small car parking sheds to 90 m (+), wide clear span aircraft hangars to low-rise multi-storey buildings. Almost every conceivable building use has been achieved using the pre-engineered building approach.
The most common applications of pre-engineered buildings are:
Industrial: Factories, Workshops, Warehouses, Cold stores, Car parking sheds, Slaughter houses, Cement plants, Steel rolling mills
Commercial: Showrooms, Distribution centers, Supermarkets, Restaurants, Offices, Service stations, Shopping centers
Institutional:Schools, Exhibition halls, Hospitals, Theaters, Auditoriums, Sports halls, Malls, Stadiums, Universities
Aviation & Military:Aircraft hangers, Administration Buildings, Residential barracks, Support facilities
Recreational:Gymnasiums, Swimming pool enclosures, Indoor tennis courts
Agricultural:Poultry-Dairy Farms, Greenhouses, Grain storage, Animal confinement
Steel Joists
Open web steel joist (OWSJ) is a lightweight steel truss consisting, in the standard form, of parallel chords and a triangulated web system, proportioned to span between bearing
The engineering section employs a team of design and detailing engineers equipped with the latest and most advanced software for both disciplines. All works are closely monitored to ensure that it
Steel Fabrication
ASSENT is one of the leading steel fabrication company in Dubai. We deliver experienced and dependable steel manufacturing and fabrication solutions for
Steel Erection
With over a decade of experience and a team of industry experts, ASSENT is a trusted Steel Erection Company in Dubai, UAE. We aim to provide a complete,
ASSENT provides top-of-the-line structural steel fabrication services. ASSENT works with the best designers and engineers to ensure that all projects meet high standards of excellence and to provide
The components of a Pre-engineered building (PEB) are manufactured at our plant according to the carefully engineered design, drawn as per the client’s specific project requirements. This
Cladding
ASSENT is one of the largest manufacturers of cold-rolled steel frame structures in the Middle East. We offer a wide range of panels and profiles to suit the industrial and commercial needs
EBS is capable of designing all kind of high complex steel structures such as high rise buildings, airport terminal buildings and industrial structures for process, petroleum and power plant
EBS has a total site area of 140,000 sq/m including 45,000 sq/m of covered fabrication area and 70,000 sq/m of storage area with the capacity to produce in excess of 70,000t of fabricated steelwork
Since the formation of Emirates Building Systems in 1997, Emirates building Systems has developed an excellent reputation and strong presence as one of the regional’s premier steel fabricator
Industrial Structures and Buildings.
Its design capacity, its substantial resources, its considerable output, its commitment to service make EBS a choice supplier for large industrial and
Pre-engineered buildings are defined by the following geometrical parameters: Building width, Length, Eave height, Roof slope, Sidewall bay spacing, end wall bay spacing and main frame module
Mezzanine
A mezzanine is an elevated floor for use as office or store area. The mezzanine framing is connected to main frame and intermediate columns for support. The mezzanine framing consists of
EBS offers profile to suit structural, architectural, thermal lighting and corrosive circumstances. Structural constraints are satisfied by the range of corrugation spacing, thickness and materials
EBS also offers steel deck for steel buildings or mezzanines to suit structural specifications. There are two profiles available in EBS production line; they are EBS50X225 and EBS75X300 with covering
EBS offers fabrication and supply of crane bridge girders for over head cranes. Most girders are from plate formed box section. EBS plant is well equipped with advance fabrication facilities for
On the Middle-East and Regional scale of the Construction Business, CSCEC ME L.L.C. has been a world class leaders and has executed in some of the complex projects of various specialised disciplines
General Contracting
In normal traditional engagement for project deliverables in the construction industry where the Owner engages the Designer and Contractor separately, CSCEC-ME
China State Construction Engineering Corporation Middle East (CSCME) Infrastructure Division has been operating in the region since 2006, in these 6 years the division has added significant strength
China State Construction Engineering Corporation Middle East (CSCME) Mechanical, Electrical and Plumbing (MEP) division has been operating in UAE since 2003 along with the core CSCME’s building
The PEB Steel Structure of a Pre-Engineered Steel Building generally accounts for over 80% of the weight of the Pre-Engineered Steel Building. This 80% is an average and may change plus or
The unit of measure of hot rolled structures (structural steel) is the metric ton (MT). Hot Rolled Steel Structures applications include Multi Storey low rise buildings, equipment
Building Accessories and special buyouts (SBO’s)include sliding doors, rollup doors, personnel doors, fiberglass insulation, sandtrap louvers, windows, ridges ventilators. Some are
Mabani erection team is comprises of highly qualified and well trained site engineers and safety officers. The team has completed more than 500 projects in the GCC, Meddle & Far
Blast & Paint
Mabani state of the art blasting, painting & material handling system produce the highest quality with most enduring coating finish. Mabani has the most advanced and
The basic parameters that define a pre-engineered building are: Building width, Building length, Building height, Roof slope, End bay length, Interior bay length and Design loads.
Width
Length
Zamil Steel pre-engineered buildings are custom-designed to meet your exact requirements. The most common Primary Framing systems are shown below. Practically any frame geometry is possible. Consult
Purlins, girts and eave struts are secondary structural members used to support the wall and roof panels. Purlins are used on the roof; girts are used on the walls and eave struts are used at the
Nearly 70% of all single storey non-residential construction now utilizes preengineered buildings. Applications range from small car parking sheds to 90 m (+), wide clear span aircraft hangars to
The panels used in the construction of Zamil Steel Pre-Engineered Buildings are composed of the following:
Base metal of either Galvalume coated steel conforming to ASTM A 792M Grade 345B or
Liner panels have one metal skin surface with polystyrene foam board adhered to it for better insulation. In the past 20 years, end-users, contractors and consultants have become increasingly aware
Eave gutters, downspouts, curved eaves, wall flashings and trims are produced from the same material (base metal, thickness, substrate coating, paint finish and color) as the wall panels of the
Drawings
Zamil Steel produces its own shop drawings for the fabrication of your steel joists, trusses, structural steel components, steel deck and girts. For project design, bid preparation or
Open web steel joist (OWSJ) is a lightweight steel truss consisting, in the standard form, of parallel chords and a triangulated web system, proportioned to span between bearing points.
The main use
Steel Decks
Steel deck is a cold formed corrugated steel sheet supported by steel joists or beams. It is used to support concrete or insulating membrane of a roof.
Zamil steel decks are
Combining Hambro steel joists with poured concrete, the system consists of hybrid concrete/steel T-beams running in one direction and an integrated continuous slab in the other (see drawing below).