DASHPROJECTS offers one of the most comprehensive Pre-engineered steel buildings-PEB product portfolios globally, with applications in major market segments including heavy industry, infrastructure,
ROOF & WALL PANELS
ROOF & WALL (AVAILABLE IN ALL REGIONS)
DASH standard steel panels are 0.5 mm or 0.6 mm thick and have a minimum yield strength of 345 MPa. Steel panels are hot dipped and galvanized with zinc or zinc-aluminium coating. Galvanized materials conform to G90 for 275 grams per square metre according to ASTM A653. Zinc-Aluminium coated materials conform to AZ150 according to ASTM A792.
DASH panels are prepared with a multilayered coating system to ensure long life and optimum coating adherence. The base material is pretreated, before applying a corrosion resistant primer and top coat. The combined thickness of the painted film is 25 microns on the front side and 12 microns on the reverse side.
DASH RIB / ROOF (KR)
DASH Roof profile is strong and cost effective and was developed specifically for roofing applications. The bearing leg design permits easier installation and maintenance, supports thicker layers of insulation and allows easier curvature for a visually appealing finish.
| Coverage Arear | : | 1000 mm | Rib Depth | : | 32 mm |
DASH WALL (KW)
DASH Wall is a cost effective, partially concealed fastener panel with a sculptured valley shape between the major ribs for a superior architectural look for external walls.
| Coverage Arear | : | 1000 mm | Rib Depth | : | 26 mm |
CONCEALED FASTENER (MIDDLE EAST & AFRICA REGION ONLY)
Concealed Fastener Single Skin Cladding (TYPE KC)
The concealed fastener single skin cladding type KC is used for exterior wall cladding and internal wall and roof liners. The panels have interlocking tongue and groove joints. The standard panels are available in 0.6 mm nominal thickness.
Concealed Fastener Sandwich Panel Cladding (Type KCIP)
The DASH concealed fastener insulated panel cladding system KCIP consists of insulated panels with generally flat outer and inner facings. The panels have interlocking tongue and groove joints with fasteners concealed within the joints. The specification of the panel facings is same as for single skin KC panels. This system has very low heat transmission values, a high strength to weight ratio and are quick to assemble, hence provide a cost effective solution on a wide range of cladding applications.
STANDING SEAM ROOF SYSTEMS
KSS 600 (India Region Only)
DASH Standing Seam Panel systems (KSS-600), with double lock standing seam, eliminates the risk of leakage at fasteners at side and end provides excellent protection in all weather conditions. It assures consistent weather tightness with virtually maintenace free performance for many years.
The KSS-600 roof system is the most specified seam roof system in the market since many DASH's KSS-600 Standing Seam Roof System has received the prestigious Factory Mutual Approval (FM approval) from USA. The FM approval is a certification for the high product quality and reliability of this roofing system.
KSS 450 (India and South East Asia region only)
DASH DECK
DASH Deck Panels are used in high rise buildings, office buildings and mezzanine floors in industrial buildings and warehouses. These decks can be used as a permanent shuttering to support the wet concrete and help in creating composite slabs and floor beams. The continuous flange stiffeners and deep embossments increase the load carrying capacities. They provide for a stable and rigid working platform without any need of propping. These panels are roll formed from hot dip galvanized coils of 345 MPa with thickness starting from 0.6 mm to 1.2 mm.
DASH Deck with 40 mm and 41 mm depth (Middle East & Africa region only)
DASH Deck with 54 mm depth & DASH Deck with 75 mm depth (India region only)
DASH Deck with 55 mm depth (South East Asia region)
CURVED CLADDING
This type of cladding uses the DASH Roof profile with width coverage of 1 m and a variable curve radius. They also add an extra advantage to the aesthetics of the building.
DASH STANDARD COLORS
Arctic White, Caribbean Blue, Desert Beige, Sun Gold, Autumn Green, Galvalume/AluZinc
DASHPROJECTS Pre-Engineered Steel Buildings (PEB)
The main components of a PEB are built up at the plant with strict adherence to the carefully engineered design and according to the
The PEB (Pre-Engineered Building) concept or the Metal Building System was first developed in the USA after World War II, as one of the solutions for the increasing
For a comparison of Pre Engineered Steel Buildings and Conventional Steel Buildings, please click on the below image:
PEB vs
DASHPROJECTS produces sandwich panels in 6 thicknesses: 35 mm, 50 mm, 75 mm, 100 mm, 125 mm and 150 mm, with an excellent slip joint connection for structural strength and weather
The structural steel division at DASHPROJECTS has the capability and capacity to supply structural steel buildings for selected types of projects, including (but not limited to):
Any metal building system, no matter how well designed, may become a continuous source of problems if installed incorrectly. Erection of metal buildings is a specialized field in which
At DASHPROJECTS, our commitment is to always provide:
The fastest response to a request for quotation
The most competitive prices
Proposal drawings to help visualize your
Frames in PEB are mainly rigid frames – comprise of Taper Columns & Rafters, are built using the state of art technology. Splices plates are welded to the ends of the tapered
SSIPL HI-RIB Sheet Profile
Metals panels are the most attractive features of Metal Building System, having contributed mightily for the growing popularity of the Metal Buildings. The term
SSIPL Standing Seam Roof System - SSR 600
Standing Seam blends the aesthetics of an architectural panel with the strength of a structural panel. These panels have a good uplifts ratings assuring
Insulated Roof and wall Cladding
Heating or cooling is one of the largest operating expense in a building. That's why it is important that each building has good thermal insulation adapted for
When Crane System is required, SSIPL supply includes Columns, Rafters, Brackets, Crane runway beams & lateral tie that support crane system. Clients have to provide complete crane data
The standard mezzanine framing system consists of a steel deck support by joists into main mezzanine beams. If required by design loads, the main beams shall also be supported by
Typical Root Platform
Section of Typical Root Platform
Single Flight Staircase
Elevation: Single Flight Staircase with Mid-Landing
Plan: Single Flight Staircase with Mid-Landing
Double Flight Staircase
Isometric : Curved Eaves
Roof Extension at Eave (without Soffit)
Roof Extension at Eave (with Soffit)
Canopy with Curved Eaves with Bottom
Fascia System
Flush Fascias with Eave Gutter
Typical Sidewall Section forFlush FasciaTypical Endwall Section forFlush Fascia
Jack Beams are used to make economical as well as safe approach for creating longer bay length when large unobstructed space, is required. Common bay lengths (5,6,7,8,9 & 10) can be
Standard Trims & Flashing
Gable Trim (GT1)
Eave Gutter (GU1)
Eave Trim (ET1)Single Ridgecap (SRC-1)
Ridgevent System
S-Type Louver Detail
Roof Monitor
Turbovent Fixing Detail
Gutter / Downspout Fixing To Wallpanel Using
Described in few words, pre-engineered buildings are ideal for any non-residential low-rise building. Applications of pre-engineered buildings are numerous. Browse through our library
Purlins, girts and eave struts are secondary structural members used to support the wall and roof panels. Purlins are used on the roof; girts are used on the walls and eave struts are used at the
DashProjects offers a complete line of Wall/Roof panels, panel related accessories, trims, purlins, girt, eave gutters, downspouts, curved eaves, wall flashings and louvers for a wide range of
The panels used in the construction of DashProjects Pre-Engineered Buildings are composed of the following:
Base metal of either Galvalume coated steel conforming to ASTM A 792M Grade 345B or
Liner panels have one metal skin surface with polystyrene foam board adhered to it for better insulation. In the past 20 years, end-users, contractors and consultants have become increasingly aware
Drawings
DASHPROJECTS produces its own shop drawings for the fabrication of your steel joists, trusses, structural steel components, steel deck and girts. For project design, bid preparation or
Open web steel joist (OWSJ) is a lightweight steel truss consisting, in the standard form, of parallel chords and a triangulated web system, proportioned to span between bearing points.
The main use
Steel deck is a cold formed corrugated steel sheet supported by steel joists or beams. It is used to support concrete or insulating membrane of a roof.
DASHPROJECTS decks are based on load
Combining DASHPROJECTS joists with poured concrete, the system consists of hybrid concrete/steel T-beams running in one direction and an integrated continuous slab in the other (see drawing below).
The success of any project involving steel-intensive construction is dictated by the efficiency in erection of the structural steelwork. With a proven track record in regards to safety, our
Primary members are the main load carrying and support members of a pre-engineered building. The main frame members include columns, rafters and other supporting members. The shape and size of these
Secondary structural framing refers to purlins, girts, eave struts, wind bracing, flange bracing, base angles, clips and other miscellaneous structural parts.
Purlins, girts and eave struts are cold
In addition to the supply of steel building structures, DASHPROJECTS offers erection services through its authorized builders.
There are over 300 DASHPROJECTS certified builders worldwide. They have
Steel exhibits desirable physical properties that make it one of the most versatile structural materials. Some of its properties such as strength, uniformity, light weight, ease of use, etc., make it
STEEL VS CONCRETE
Evluation Criteria
Peb Building
Concrete Building
Steel Advantage
Building Dimensions
Suitable for spans 20-30m. Can sustain much larger spans.
When it comes to fit out, no one has a better track record than DASHPROJECTS. But we’ve never been much for resting on our laurels.
When it comes to professional
Great technology is no longer an afterthought. We believe all work environments are technology environments.
We believe all business environments are technology
When it comes to construction, our vision is our customer's vision. We drive dynamic solutions to reach exceptional results.
When it comes to construction, our vision
DASH PROJECTS Central Engineering Department is located in DUBAI UAE
Our engineering department is composed of 2 sections; Steel Design section & Steel Detailing section.
DASH
DASHPROJECTS (DASH) owns several factories to fabricate structural steel, Pre-engineered Buildings and material handling systems. These factories are located in Egypt, Syria and UAE .
Our factories
In DASHPROJECTS (DASH), the project management team, selected and led by the project manager, is responsible for coordinating and integrating activities across multiple functional lines:
A-The
Erection / installation of the company’s projects are implemented by developing the erection method statement considering the complexity of the Job, project schedule, site logistics,
Pre-engineered steel buildings can be fitted with different structural accessories including mezzanine floors, canopies, fascia, interior partitions etc. and the building is made water proof by use
DASHPROJECTS Structural Steel business unit had executed different categories of projects such as Industrial buildings, Airports terminals, Airport Hangers, warehouses, sport complex,
Structural steel and plate construction associated with crusher plants, cement factories, batching plants, block factories and sorting plants to be used as rock box hoppers, silos, chutes, conveyors